material modulus values pvc duct

TYPICAL PROPERTIES of PVC and CPVC - International Polymer ...

PVC is the most widely used member of the vinyl family. It is most commonly used in pipe and fittings. PVC offers ... Tensile Modulus (psi). 411,000. 430,000.

Effect of temperature on tensile properties of HDPE pipe material

In general, a similar effect was observed on yield stress, modulus of elasticity and yield strain in all these materials. ... CPVC and PVC pipe materials, used in comparable applications. .... at 70uC, the scatter in the values of yield strength and.

Physical Properties of PVC & CPVC Pipe - PVC Pipe Supplies

PVC & CPVC Corrosion Resistant Industrial Pressure Pipe. Physical ... PVC Value ... Tensile Modulus of Elasticity, ... Clean Room Materials Flammability Test.

PVC Pipe Specifications, Sizes & Pressure Ratings - Professional ...

PVC Pipe Specifications, Sizes & Pressure Ratings. PVC Pipe Physical Properties. GENERAL. Value. Test Method ... ASTM D638. Tensile Modulus of Elasticity, psi @ 73°F. 420,000. ASTM D638 ... Material Carbonizes. 425°F. Limiting Oxygen...

Young's Modulus - Tensile and Yield Strength for common Materials

Modulus of Elasticity - and Ultimate Tensile and Yield Strength for steel, glass, wood and ... A53 Seamless and Welded Standard Steel Pipe - Grade A, 331, 207 .... of a solid due to stress" - change in dimension divided by the original value of the ... can undergo before moving from elastic deformation into plastic deformation.

Pipe Technical Data Reference - Aegion

PVC dimensions (minimum wall thickness and outside diameter) are per AWWA C900. ... classification value of 7,000 PSI for short term tensile strength [ASTM D1784] ... calculated using the Modulus of Elasticity (400,000 PSI for PVC and 28,200 ... published Poisson's Ratio for the given material [Unibell Handbook of PVC,...

Impact, Bending, Flexural and Compressive Strength Tests On a ...

strength and modulus of elasticity of the material. While the value of fracture ... Samples were cut from a U-PVC pipe that ... The values of Young's modulus (E).

CPVC pipe - ResearchGate

The yield stress and elastic modulus decreased logarithmically with decreasing ... The value of fracture strain remained almost constant with crosshead speed at 50 degrees C and below. .... temperature and decreasing strain rate for both PVC.

Material Technical Unit of PVC Duct Characteristics Measure ... - Iboco

Material Technical. Unit of. PVC Duct. Characteristics. Measure. Standard. Value. CHEMICAL-PHYSICAL PROPERTIES. Specific gravity g/cm^3. ASTM D792. 1.55. H2O 73,4° F ... Modulus of elasticity at flexion. MPa. ASTM D790. 3200.

Analysis of PVC Pipe-Wall Viscoelasticity during Water Hammer

importance of pipe-wall viscoelasticity in hydraulic transients in PVC pipes. .... J0 =1/E0; E0 =Young's modulus of elasticity of the pipe;. Jk =creep compliance of the ..... less than instantaneous elastic strain value 6% and the creep function J t...

1Mechanical Properties of Polymers - Smithers Rapra

understand effectively the behaviour of plastic materials, and to give a .... *These are typical room-temperature values of Notched Izod impact strength. ... Tensile strength (tensile modulus) tests with or without preloading, according to ..... In many applications such as those involving an interference fit (e.g., pipe couplings,.

Mid-States: CPVC Physical Properties

Tensile Modulus (psi), 73°F, 430,000, ASTM D-638 ... ASTM D1785 - PVC Schedule 80 pipe specifications, ANSI B2.1 - Specifications for flange type fittings.

Tensile Strength of different plastics

... (PVC) – Pen case. • Polyvinyl Chloride (PVC) – Shrink Wrap ... Packaging films. – Tarp. Theoretical Young's Modulus: ... Theoretical Value: 0.11 to 0.45 GPA.

PVC Properties - Vinidex

Where the discussion refers to a specific type of PVC pipe, that type will be explicitly ... The elastic modulus, yield stress and ultimate tensile strength are generally lower than ... Some comparative values are shown for other pipe materials.

pvc pipe performance factors - Rinker Materials

PVC pipe, like all flexible pipe products, is very dependent on the .... While dumped angular shaped crush rock may develop an E' (soil modulus) value of.

PVC Strength - PVC

Sep 21, 2015 ... The tensile modulus is also known as the Young's Modulus, which is expressed in terms of the ... Higher values show higher impact strength.

PVC Pipe Engineering Properties - North American Pipe

PVC Pipe Engineering Properties. Mechanical Properties. Property. Value. Restrictions ... Pressure Rated PVC 1120 Materials, ... Tensile (Young's) Modulus.

PVC Pipe Materials, Cell-Class Explained - Royal Building Products

The material used to produce PVC pipe is known as “PVC compound. ... third & Fourth Cells address tensile strength & tensile Modulus ... Below is part of an astM d1784 table that gives the values of the 3rd and 4th cells for compounds used...

Chapter 3 - Material Properties - Plastics Pipe Institute

a PE pipe can vary somewhat depending on the PE material from which it is made ... (PVC). These can be re-melted upon the application of heat. The solid state of ..... Accordingly, the apparent modulus values within this stress range may.

The Effect of Several Service and Weathering Parameters on ...

sile properties of PVC pipe's row material were investigated. The selected ... UV treatment didn't show a significant effect on the yield stress and modulus of elasticity. This is an .... speeding up temperature of 70˚C. This value can be used.